PIN TO DRG 613.44.058 T-72

PIN TO DRG.NO.613.44.058,TECHNICAL REQUIREMENT AS PER SPEC. NO.OFM/TDS/TRACK-72/02

DRG.NO.613.44.058

• 1. Cold drawing process line of adequate capacity to manufacture cold deformed hexagonal bar. 2. Suitable end finishing machine for carrying out cutting of cold deformed hexagonal bar to required length by cold machining. 3. Turning / thread rolling / thread forming machine.
• Hot Rolling. Isothermal heat treatment line to achieve required mechanical properties as specified. Shot Blasting Facility of Zinc coating and Chromate passivation. Facility for removal of Hydrogen Embrittlement.

• Crack detection testing facility. Bend removing (straightening) machine. Bend test facility. Mechanical, metallurgical and Chemical analysis testing facilities to test the required parameters as specified in specification no.OFM/TDS/TRACK-72/02.

NUT TO DRG 613.44.071 T-72

NUT TO DRG.NO.613.44.071,TECHNICAL REQUIREMENT AS PER SPEC. NO.OFM/TDS/TRACK-72/O3

DRG.NO.613.44.071

• 1. Cold drawing process line of adequate capacity to manufacture cold deformed hexagonal bar.2. Suitable end finishing machine for sizing of cold deformed hexagonal bar to required length by cold machining.
• Hot Rolling. Suitable heat treatment line to achieve required mechanical properties as specified. Facility of Zinc coating and Chromate passivation.

• Crack detection testing facility. Mechanical, metallurgical and Chemical analysis testing facilities to test the required parameters as specified in specification no.OFM/TDS/TRACK-72/03.

ROLLING RING ASSY 250 KG

ROLLING RING ASSY. TO DRG. No. ARDE 9501-01 DET 18 (WITHOUT PHOSPHATED) . [DRG. ENCLOSED]

ARDE 9501-01 DET 18

• 1. Adequate hydraulic press machine (min. 200 ton) for Fabrication (sheet metal work) 2. Welding

• Testing facilities as per relevant drawing

RUBBERISING OF SHORT BUSHING

RUBBERISING OF SHORT BUSHING TO DRg.No.613.44.061, AS PER SPEC.No.OFM/TDS/TRACK-72/04 AND COMPLETE ASSEMBLY DRg.No.613.44.057 Cb.

DRg.No.613.44.061,

• 1. Injection moulding machine.

• 1. Tensile strength testing facility. 2. Hardness testing facility. 3. Brittleness testing facility at low temperature. 4. Bonding strength test facility. 5. Service life (Endurance) test facilities. 6. Testing facilities as per specification no. OFM/TDS/TRACK-72/04.

RUBBERISING OF MEDIUM BUSHING.

RUBBERISING OF MEDIUM BUSHING TO DRg.No.613.44.060,AS PER SPEC.No.OFM/TDS/TRACK-72/04 AND COMPLETE ASSMBLY- DRg.No.613.44.056 Cb.

• 1. Injection moulding machine.

• 1. Tensile strength testing facility. 2. Hardness testing facility. 3. Brittleness testing facility at low temperature. 4. Bonding strength test facility. 5. Service life (Endurance) test facilities. 6. Testing facilities as per specification no. OFM/TDS/TRACK-72/04.

RUBBERISING OE LONG BUSHING.

RUBBERISING OF LONG BUSHING TO DRg.No.613.44.059,AS PER SPEC.No.OFM/TDS/TRACK-72/04 AND COMPLETE ASSEMBLY DRg.No.613.44.055 Cb.

DRg.No.613.44.059

• 1. Injection moulding machine.

• 1. Tensile strength testing facility. 2. Hardness testing facility. 3. Brittleness testing facility at low temperature. 4. Bonding strength test facility. 5. Service life (Endurance) test facilities. 6. Testing facilities as per specification no. OFM/TDS/TRACK-72/04.

SHORT BUSHINGS FOR T-72

SHORT BUSHING TO DRG. NO.613.44.061, TECHNICAL REQUIREMENTS AS PER SPEC. NO. OFM/TDS/TRACK-72/01.

• DRG. NO.613.44.061
• 1. Cold drawing process line of adequate capacity to manufacture cold deformed pipe with inner hexagonal profile.2. Heat treatment line to achieve required mechanical properties as specified.3. Suitable end finishing machine for carrying out cutting of cold deformed pipe with inner hexagonal profile to required length by cold machining.
• Hot Rolling.

• Mechanical, metallurgical, chemical analysis and crack detection testing facilities to test the required parameters as specified in specification no. OFM/TDS/TRACK-72/01.

MEDIUM BUSHING T-72

MEDIUM BUSHING TO DRG. NO.613.44.060, TECHNICAL REQUIREMENTS AS PER SPEC. NO. OFM/TDS/TRACK-72/01.

DRG. NO.613.44.060

• 1. Cold drawing process line of adequate capacity to manufacture cold deformed pipe with inner hexagonal profile.2. Heat treatment line to achieve required mechanical properties as specified. 3. Suitable end finishing machine for carrying out cutting of cold deformed pipe with inner hexagonal profile to required length by cold machining.
• Hot Rolling.

• Mechanical, metallurgical, chemical analysis and crack detection testing facilities to test the required parameters as specified in specification no. OFM/TDS/TRACK-72/01.

LONG BUSHING T-72 TRACK

LONG BUSHING TO DRG.NO.613.44.059,TECHNICAL REQUIREMENT AS PER SPEC.NO.OFM/TDS/TRACK-72/01.

DRG.NO.613.44.059

• 1. Cold drawing process line of adequate capacity to manufacture cold deformed pipe with inner hexagonal profile. 2. Heat treatment line to achieve required mechanical properties as specified. 3. Suitable end finishing machine for carrying out cutting of cold deformed pipe with inner hexagonal profile to required length by cold machining
• Hot Rolling.

• Mechanical, metallurgical, chemical analysis and crack detection testing facilities to test the required parameters as specified in specification no. OFM/TDS/TRACK-72/01.

Tape Nylon for Aerospace Purpose 25 MM Black

IS-4228-1979 (RA-2003) (Reaffirmed 2013) and Prov. Specn No.S/6421/Bag Sleeping Lt Wt/TC-6

• Weaving
• Processing

• Visual
• Mechanical
• Chemical

Nylon Sewing Thread OG Vol No L-2

IS-4229 (RA-2008) (RA 2013) and Prov. Specn. No. S/6421/Bag Sleeping Lt Wt/TC-6

• Doubling
• Processing

• Visual
• Mechanical
• Chemical

Toggle ( Cord Stopper)

Prov. Specification No. S/6421/Bag Sleeping Lt Wt/TC-6

• Moulding

• Visual
• Mechanical
• Chemical

Fabric Nylon PU Coated WP OG 115 GSM

Specn. No. S/6421/Bag Sleeping Lt Wt/TC-6

• Weaving
• Processing
• Coating

• visual
• mechanical
• chemical

Fastener Hook and Loop Tape OG

IS-8156-1994 (RA-2009) and Prov. Specn. No. S/6421/Bag Sleeping Lt Wt/TC-6

• Weaving
• Raising
• Processing

• Visual
• Mechanical
• Testing

Ladder Lock for Tape Width 25 MM

Prov. Specn. No. S/6421/bag Sleeping Lt Wt/TC-6

• Moulding

• Visual
• Mechanical
• Chemical

Tape Nylon For Aerospace Purpose 25 MM OG

IS-4228-1979 (RA-2003) (Reaffirmed 2013) and Prov. Specn. No. S/6421/Bag Sleeping Lt Wt/TC-6

• Weaving
• Processing

• Visual
• Mechanical
• Chemical

Quilt Outer for Bag Sleeping for -20 degree Centigrade

Prov. Specification No. S/6421/Bag Sleeping Lt Weight/TC-6

• Quilting

• Visual
• Mechanical
• Chemical

Quilt Inner for Bag Sleeping for -20 degree Centigrade

Prov. Specification No. S/6421/Bag Sleeping LT Weight/TC-6

• Quilting

• Visual
• Mechanical
• Chemical

Two Way open End Heavy Duty Zipper 150 Cms

IS-14181-2002 (RA-2013) & Provisional Specification S/6421/Bag Sleeping Lt Weight/TC-6

• Weaving
• Moulding
• Processing

• visual
• Mechanical
• Chemical

Cord Nylon Braided OF 2452 N

JSS: 4020-9-1999, Provisional specification S/6421/Bag Sleeping Lt. Wt./ TC-6

• Braiding
• Processing

• visual
• Mechnical
• Chemical

FORG.FOR GEAR INTERMED.175-45-005F

FORG.FOR GEAR INTERMED.175-45-005F

175.45.005

• AS PER DRG SPECIFICATION

• AS PER DRG SPECIFICATION

FORG.FOR GEAR DRIVING 175-45-004

FORG.FOR GEAR DRIVING 175-45-004

175.45.004

• AS PER DRG SPECIFICATION

• AS PER DRG SPECIFICATION

Tape Nylon 2.54 cm + 1 – 0 U/D BS: 250 Kg

ADRDE/Specn/64

• AS PER SPECIFICATION

• AS PER SPECIFICATION

FABRICATION OF DANGER BUILDING COAT WHITE THROUGH TRADE

SPECN-AS PER TECHNICAL PARTICULARS ENCLOSED

• AS PER SPECIFICATION/DRAWING

• AS PER SPECIFICATION/DRAWING

FABRICATION OF DANGER BUILDING TROUSERS WHITE THROUGH TRADE

SPECN-AS PER TECHNICAL PARTICULARS ENCLOSED

• AS PER SPECIFICATION/DRAWING

• AS PER SPECIFICATION/DRAWING

IC Bracket to Drg.No. SK-3706/34*7 Duly Heat Treated To:T Condition

IC Bracket to Drg.No. SK-3706/34*7 Duly Heat Treated To:T Condition

IC Bracket to Drg.No. SK-3706/34*7 Duly Heat Treated To:T Condition

• Machining and Assy.

• As per manufacturing Technology machining document

NIV PACK FRAME

FOR - DRAWING NO.CQA(GS)/US/557 READ- DRAWING NO.CQA(GS)/US/557 except that :- Drg sheet No. 2 of 3 Dtd :24.04.2019

• AS PER SPECIFICATION

• AS PER SPECIFICATION

HOUSING WITH FERRULE & RUBBER SLEEVE FOR P.P. MIRAG 2000/SEA HARRIER A/C

SPECN-ADRDE/1357(a)

SPECN-ADRDE/1357(a)

• AS PER SPECIFICATION

• AS PER SPECIFICATION

Sub-Assy of Spring for Auxiliary Spring PTA-R Parachute

CQA(GS)/US/563

• AS PER SPECIFICATION

• AS PER SPECIFICATION

DETACHABLE ALIGNMENT RING

DRG.NO.:ADRDE/1296-G(b) DRD/29/98.

• AS PER DRAWING/SPECIFICATION

• AS PER DRAWING/SPECIFICATION

BALL TYPE SPRING(PSM SERIES)

ADRDE/1332(b)

• AS PER DRAWING/SPECIFICATION

• AS PER DRAWING/SPECIFICATION

CORDAGE POLYESTER HEAT SET BS:364 KG WITH RED THREAD

ADRDE/SPECN/74(a)

• AS PER SPECIFICATION

• AS PER SPECIFICATION

CORDAGE POLYESTER HEAT SET BS:318KG

ADRDE/SPECN/74(a)

• AS PER SPECIFICATION

• AS PER SPECIFICATION

MANUFACTURING AND SUPPLY OF BODY AS PER DRG NO K 4001STR3 WITH FIRMS MATERIAL REQUIRED FOR TAR

MANUFACTURING AND SUPPLY OF BODY AS PER DRG NO K 4001STR3 WITH FIRMS MATERIAL REQUIRED FOR TAR

K 4001STR3

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

BOLT CARRIER AS PER DRG NO K 2001STR2 IN FULLY FINISHED CONDITION WITH FIRMS MATERIAL REQUIRED FOR TAR

BOLT CARRIER AS PER DRG NO K 2001STR2 IN FULLY FINISHED CONDITION WITH FIRMS MATERIAL REQUIRED FOR TAR

K 2001STR2

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

MANUFACTURING AND SUPPLY OF BOLT AS PER DRG NO K 2011 WITH FIRMS MATERIAL REQUIRED FOR TAR

MANUFACTURING AND SUPPLY OF BOLT AS PER DRG NO K 2011 WITH FIRMS MATERIAL REQUIRED FOR TAR

K 2011

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

Supply Installation and Commissioning of Pneumatic Assembly Drg No VMT SK 119 18000 11 with Festo Make Control Cabinet Part No. IN CS 3049329 for 125 mm SCCC Winding Machine as per Part List Sheet No 1 to 8 and 10 and 11 Drawing and Scope of Work attached

Supply Installation and Commissioning of Pneumatic Assembly Drg No VMT SK 119 18000 11 with Festo Make Control Cabinet Part No. IN CS 3049329 for 125 mm SCCC Winding Machine as per Part List Sheet No 1 to 8 and 10 and 11 Drawing and Scope of Work attached

Drg No VMT SK 119 18000 11

• Firm must submit the details of Manufacturing Technologies and Inspection/Testing Facilities available with the firm for manufacturing the subject items. Quality assurance plan (IF ANY) related to production and inspection to be submitted in technical bid. List of Plant & Machineries required for manufacturing of subject item to be submitted.

• Firm must submit the details of Manufacturing Technologies and Inspection/Testing Facilities available with the firm for manufacturing the subject items. Quality assurance plan (IF ANY) related to production and inspection to be submitted in technical bid. List of Plant & Machineries required for manufacturing of subject item to be submitted.

LOCK OCK WITH BUCKLE

ADRDE/1354.

• As per Specification/Drawing

• As per Specification/Drawing

ROUND 56 MM DIA

GOST 4543-71

• AS INDICATED IN THE VQC

• AS INDICATED IN THE VQC

MANUFACTURING AND SUPPLY OF FULL FINISHED COMPONENT LEAVER PLATE TO DRG NO K 2071

MANUFACTURING AND SUPPLY OF FULL FINISHED COMPONENT LEAVER PLATE TO DRG NO K 2071

K 2071

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

ELECTRIC FUZE UNCHARGED ( EMPTY) TO DRG NO. 3-027321 CD 8

ELECTRIC FUZE UNCHARGED ( EMPTY) TO DRG NO. 3-027321 CD 8

DRG NO. 3-027321 CD 8

• 1. Hydraulic Press/ Power Press Machine 2. Electroplating / Tinning Plant 3. Soldering Technique

• 1. NABL Test for ebonite Type-I unloaded as per Specification IS 6693:83 with Tensile & Impact test 2. NABL test for Copper as per specification IS 3487:94 3. NABL test for Pine rosin & Varnish as per Specification mentioned in Drawing 4. Multimeter to Test resistance 5. Tin Coating Thickness 6. General Purpose Engineering Equipment’s for measuring dimension like Vernier Caliper / Micrometer , Depth gauge etc.

IC TO DRG.NO.:TEND.922 F FOR SLIDE.(ICR-1328) 1005-001604

AS PER IC TO DRG.NO.:TEND.922 F FOR SLIDE.(ICR-1328) 1005-001604

TEND.922 F FOR SLIDE.(ICR-1328) 1005-001604

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

IC TO DRG NO.:TEND 1100 D FOR RAMP BACKSIGHT(ICR-1253)

AS PER DRG NO.:TEND 1100 D FOR RAMP BACKSIGHT(ICR-1253)

TEND 1100 D FOR RAMP BACKSIGHT(ICR-1253)

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

WRENCH, ADJUSTING FORESIGHT & LOCK NUT FORE SIGHT TO DRAWING NO.R.F.I.SK.NO.1051 *3 (MODIFIED)(FOR RIFLE 7.62 mm1A1)

AS PER DRAWING NO.R.F.I.SK.NO.1051 *3 (MODIFIED)(FOR RIFLE 7.62 mm1A1)

R.F.I.SK.NO.1051 *3 (MODIFIED)

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

SUPPLY OF SCREW PISTOL GRIP TO D.S. CAT. NO. 5305-005004 (ICR - 1380) TO LATEST D.C No.24275-SA DATED 26.02.1999 FOR DC.NO. LATEST ISSUE TO BE FOLLOWED

AS PER D.S. CAT. NO. 5305-005004 (ICR - 1380) TO LATEST D.C No.24275-SA DATED 26.02.1999 FOR DC.NO. LATEST ISSUE TO BE FOLLOWED

D.S. CAT. NO. 5305-005004 (ICR - 1380) TO LATEST D.C No.24275-SA DATED 26.02.1999

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

TE NO. D222 BO0209

TE NO. D222 BO0209

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

MFG & SUPPLY OF PIN LEAF TO D.S. CAT NO.5315-001767 DC NO.22647-SA DATED 20.08.1994 REQD IN WHITE FINISHED CONDITION (ICR 1329)

AS PER D.S. CAT NO.5315-001767 DC NO.22647-SA DATED 20.08.1994 REQD IN WHITE FINISHED CONDITION (ICR 1329)

D.S. CAT NO.5315-001767 DC NO.22647-SA DATED 20.08.1994 REQD IN WHITE FINISHED CONDITION (ICR 1329)

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

SUPPLY OF PIN AXIS HAMMER TO DS. CAT NO. 5315-009115 DC NO.25060-SA DT. 05/07/2001 REQUIRED IN WHITE FINISHED CONDITION . FOR DC NO. LATTEST ISSUE TO BE FOLLOWED. (WITH FIRMS MATER

AS PER DS. CAT NO. 5315-009115 DC NO.25060-SA DT. 05/07/2001 REQUIRED IN WHITE FINISHED CONDITION

DS. CAT NO. 5315-009115 DC NO.25060-SA DT. 05/07/2001 REQUIRED IN WHITE FINISHED CONDITION

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

SEAR SAFETY (ICR-1281) D.S. CAT No.:1005-001697, D.C.No.22816-SA DATED:20.01.1995 (ICR-1281)

AS PER DRAWING

ICR-1281

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

GUARD HAND LEFT & RIGHT ASSY. (PLASTIC) No.2, CQA(SA)/91,D.S.CAT.No.1005-007723,D.C.No.22706-SA Dt.5-11-94 IMPROVED VERSION FOR RIFLE 7.62mm 1A1 TO D.S.CAT.No.: 1005-007504, 1005-007505, 1005-007506,1005-007507,1005-001593,1005-1718,

AS PER DRG No.2, CQA(SA)/91,D.S.CAT.No.1005-007723,D.C.No.22706-SA Dt.5-11-94 IMPROVED VERSION FOR RIFLE 7.62mm 1A1 TO D.S.CAT.No.: 1005-007504, 1005-007505, 1005-007506,1005-007507,1005-001593,1005-1718,

DRG No.2, CQA(SA)/91,D.S.CAT.No.1005-007723,D.C.No.22706-SA Dt.5-11-94 IMPROVED VERSION FOR RIFLE 7.62mm 1A1 TO D.S.CAT.No.: 1005-007504, 1005-007505, 1005-007506,1005-007507,1005-001593,1005-1718,

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

SCREW HAND GUARD TO D.S.CAT. NO. 5305-005008 DC NO.24312-SA DATED 03-04-99 (ICR-1196) LATEST ISSUE SHOULD BE FOLLOWED.

AS PERD.S.CAT. NO. 5305-005008 DC NO.24312-SA DATED 03-04-99 (ICR-1196) LATEST ISSUE SHOULD BE FOLLOWED.

(ICR 1196) D.S.CAT. NO. 5305-005008 DC NO.24312-SA

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

SCREW LOCKING HINGE PIN D.S.CAT.No.: 5305-018166, D.C.No.:24629-SA, DATED:02/02/2000 FOR D.C.No. LATEST ISSUE TO BE FOLLOWED.

AS PER D.S.CAT.No.: 5305-018166, D.C.No.:24629-SA, DATED:02/02/2000 FOR D.C.No. LATEST ISSUE TO BE FOLLOWED.

(ICR-1195) D.S.CAT.No.: 5305-018166, D.C.No.:24629-SA, DATED:02/02/2000

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

Bracket Module Containing:- A) Bracket RHS to Drg.No.1403-01-01-09RHS B) Bracket LHS to Drg.No.1403-01-01-09LHS

Bracket Module Containing:- A) Bracket RHS to Drg.No.1403-01-01-09RHS B) Bracket LHS to Drg.No.1403-01-01-09LHS

A) Bracket RHS to Drg.No.1403-01-01-09RHS B) Bracket LHS to Drg.No.1403-01-01-09LHS

• melting facility & casting facility
• firm should have photostatting & heat treatment facility or Tie-up with other unit.
• firm should have foundry for steel items.
• . firm should have laboratory for chemical testing before and after drawn sample or Tie-up with the other laboratory unit.
• firm should have machinery facility for steel component.

• chemical lab & mechanical lab
• Firm should have painting facility.

Electrical Assy. Drg. No. VMT-SK-119-19000-11 for Winding Machine 125MM SCCC (As per Part List 09 Sheets, Drgs. & Scope of Work Enclosed), Qty: 1 Set

Electrical Assy. Drg. No. VMT-SK-119-19000-11 for Winding Machine 125MM SCCC (As per Part List 09 Sheets, Drgs. & Scope of Work Enclosed), Qty: 1 Set

Drg. No. VMT-SK-119-19000-11

• Firm must submit the details of Manufacturing Technologies and Inspection/Testing Facilities available with the firm for manufacturing the subject items. . Quality assurance plan (IF ANY) related to production and inspection to be submitted in technical bid. List of Plant & Machineries required for manufacturing of subject item to be submitted.

• Firm must submit the details of Manufacturing Technologies and Inspection/Testing Facilities available with the firm for manufacturing the subject items. . Quality assurance plan (IF ANY) related to production and inspection to be submitted in technical bid. List of Plant & Machineries required for manufacturing of subject item to be submitted.

CONNECTING PIECE REAR TO PT NO 1145139

CONNECTING PIECE REAR TO PT NO 1145139

• As per tender document Annexure L

• As per tender document Annexure L

CONNECTING PIECE FRONT TO PT NO 1148858

CONNECTING PIECE FRONT TO PT NO 1148858

• As per tender document Annexure L

• As per tender document Annexure L

BODY PR. DIE CASTING WITHOUT GROOVE TO DRG.NO. ODD/C/1028/1

BODY PR. DIE CASTING WITHOUT GROOVE TO DRG.NO. ODD/C/1028/1

DRG.NO. ODD/C/1028/1

• As per Sr.No.65 of Annexure-A with OFB Letter No.OFB/108/Online VR/QC dated 12.02.2019

• As per Sr.No.65 of Annexure-A with OFB Letter No.OFB/108/Online VR/QC dated 12.02.2019

PACKING FITMENT FOR 155 MM BBU AS PER DRG NO PROP SK 802

PACKING FITMENT FOR 155 MM BBU AS PER DRG NO PROP SK 802

PACKING FITMENT FOR 155 MM BBU AS PER DRG NO PROP SK 802

• SIZING/CUTTING

• a) Raw material foam test from NABL Lab as per specification IND/ME 913 (a) Prov 2004. b) General Purpose engineering equipment's like Vernier, Scale, Tape etc. to measure dimensions.

PACKING BOX FOR 155 MM BBU AS PER DRG NO PROP SK 803

PACKING BOX FOR 155 MM BBU AS PER DRG NO PROP SK 803

PACKING BOX FOR 155 MM BBU AS PER DRG NO PROP SK 803

• 1. PLASTIC INJECTION/ROTO MOULDING 2. GRINDERS 3. OVEN/HOPPER DRYERS

• a) Raw material test from NABL Lab as per JSS 9330-03 (Latest issue) b) General Purpose engineering equipment’s to measure dimensions c) Mechanical test like jolt test, drop test. d) Relevant test as per specification CQA(A) 2804.

ST SQR.75 MM TO SPECN.BS:3S144:1995(1999)GD S144H LFVD WITH CAL.SILICIDE TREATMENT.INCLUSION RATINGCHART SECONDARY REFINING STEEL AS PER SPECN.IS:4163-82,i.e.THN/THK SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICATE:1.5-1,GLOBULAR OXIDE: 2.0-1.

ST SQR.75 MM TO SPECN.BS:3S144:1995(1999)GD S144H LFVD WITH CAL.SILICIDE TREATMENT.INCLUSION RATINGCHART SECONDARY REFINING STEEL AS PER SPECN.IS:4163-82,i.e.THN/THK SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICATE:1.5-1,GLOBULAR OXIDE: 2.0-1.

• As per Tender Document Annexure L

• As per Tender Document Annexure L

GUIDE TO DRG.NO.GCF/50/40803

GUIDE TO DRG.NO.GCF/50/40803 (REF.DRG.NO.4076066).

• AS PER ANNEXURE L

• AS PER ANNEXURE L

GUIDE TO DRG.NO.GCF/50/40802

TO DRG.NO.GCF/50/40802 (REF.DRG.NO.4076063)

• AS PER ANNEXURE L

• AS PER ANNEXURE L

GUIDE TO DRG.NO.GCF/50/40801

GUIDE TO DRG.NO.GCF/50/40801 (REF.DRG.NO.4076056).

• AS PER ANNEXURE L

• AS PER ANNEXURE L

GUIDE TO DRG.NO.GCF/50/40800

GUIDE TO DRG.NO.GCF/50/40800 (REF.DRG.NO.4076054)

• AS PER ANNEXURE L

• AS PER ANNEXURE L

PIN DETENT SPRING TO CQA(A) DRG. NO. 13046-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002

PIN DETENT SPRING TO CQA(A) DRG. NO. 13046-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002

• AS PER ATTACHMENT

• AS PER ATTACHMENT

PIN DETENT PIVOT TO CQA(A) DRG. NO. 13038-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002

PIN DETENT PIVOT TO CQA(A) DRG. NO. 13038-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002

• AS PER ATTACHMENT

• AS PER ATTACHMENT

WASHER TO CQA (A) DRG. NO. 13975-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002)

WASHER TO CQA (A) DRG. NO. 13975-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002)

• AS PER ATTACHMENT

• AS PER ATTACHMENT

PIN ROTOR LOCK TO CQA(A) DRG. NO. 13047-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002)

PIN ROTOR LOCK TO CQA(A) DRG. NO. 13047-0-0 (AS PER DC NO. 36804-A DATED 01/01/2002)

• AS PER ATTACHMENT

• AS PER ATTACHMENT

TE.NO. D182 G5 2344

TE.NO. D182 G5 2344

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

IDENTIFICATION LIST FOR RIFLE 7.62MM 1A1 TO CODE NO.IL/IW/29 (AS PER SPECIFICATIONS& REQUIREMENTS MENTIONED IN THE ANNEXURE)

IDENTIFICATION LIST FOR RIFLE 7.62MM 1A1 TO CODE NO.IL/IW/29 (AS PER SPECIFICATIONS& REQUIREMENTS MENTIONED IN THE ANNEXURE)

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

IDENTIFICATION LIST FOR RIFLE 7.62MM 1A1 TO CODE NO.IL/IW/29 (AS PER SPECIFICATIONS& REQUIREMENTS MENTIONED IN THE ANNEXURE)

IDENTIFICATION LIST FOR RIFLE 7.62MM 1A1 TO CODE NO.IL/IW/29 (AS PER SPECIFICATIONS& REQUIREMENTS MENTIONED IN THE ANNEXURE)

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

CAN, OIL MG MK3 DS CAT NO. 4930-000800, 1005-000336 TO 1005-000338 & 5310-002657, DC NO. 23500-SA DT.20-9-96

AS PER DS CAT NO. 4930-000800, 1005-000336 TO 1005-000338 & 5310-002657, DC NO. 23500-SA DT.20-9-96

DS CAT NO. 4930-000800, 1005-000336 TO 1005-000338 & 5310-002657, DC NO. 23500-SA DT.20-9-96

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

DS CAT NO. 1005-002050

DS CAT NO. 1005-002050

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

DS CAT NO. 1005-002050

DS CAT NO. 1005-002050

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

BOTTLE OIL MK-V, DS CAT.NO.1005-000323,1005-000324, 1005-000326,1005-000327,1005-000328, DC.NO.23296 SA-DT:21/03/96. FOR DC. NO. LATEST ISSUE TO BE FOLLOWED.

AS PER DS CAT.NO.1005-000323,1005-000324, 1005-000326,1005-000327,1005-000328, DC.NO.23296 SA-DT:21/03/96. FOR DC. NO. LATEST ISSUE TO BE FOLLOWED.

DS CAT.NO.1005-000323,1005-000324, 1005-000326,1005-000327,1005-000328, DC.NO.23296

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

As per Drawing

As per Drawing

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

LF:6583305001

LF:6583305001

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

PULL THROUGH 1A(NYLON) AS PER DS CAT NO.1005-001760 FOR DC NO. 22520-SA DATED 2.5.94 LATEST ISSUE TO BE FOLLOWED FOR RIFLE 7.62mm 1A1

AS PER DS CAT NO.1005-001760 FOR DC NO. 22520-SA DATED 2.5.94 LATEST ISSUE TO BE FOLLOWED FOR RIFLE 7.62mm 1A1

DS CAT NO.1005-001760 FOR DC NO. 22520-SA DATED 2.5.94 LATEST ISSUE TO BE FOLLOWED FOR RIFLE 7.62mm 1A1

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

LV6/MT7-3110-002686 BALL BEARING DIA. 3.175mm TOIS: 2898, 1976 GRADE 5.MATL: IS 4398-1972. (FOR ICR 72SA)

LV6/MT7-3110-002686 BALL BEARING DIA. 3.175mm TOIS: 2898, 1976 GRADE 5.MATL: IS 4398-1972. (FOR ICR 72SA)

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

PIN KEEP SPLIT 1/16" GI 5315- 000053(DIA 1.59mm X19.05mm LONG)IS:549 : 2005.

AS PER DRAWING

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE