1. Chemical & Mechanical properties as per std. given drawing.
2. Dimensional inspection, for all dimensions given in the drawing & other parameter which are mentioned in relevant drawing.
PLASTIC SLIDE FASTENER OPEN END MEDIUM SPECIAL DUTY WHITE 58CM. SPECIFICATION:- IS:14181(PART 1-3) 2002 REAFFIRMED-2013.AS PER RELEVANT CLAUSE OF SPECIFICATION.AS PER RELEVANT CLAUSE OF SPECIFICATION
Specification
PLASTIC SLIDE FASTENER OPEN END MEDIUM SPECIAL DUTY WHITE 58CM. SPECIFICATION:- IS:14181(PART 1-3) 2002 REAFFIRMED-2013.AS PER RELEVANT CLAUSE OF SPECIFICATION.AS PER RELEVANT CLAUSE OF SPECIFICATION
Drawing no.
Manufacturing Technology
as per attached list (Manufacturing Technology Files )
(i) Foundry Facility for Aluminium Casting
(ii) Heat Treatment Facility
(iii) Conventional/CNC machining
(iv) Surface Treatment
In case tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The foundry facility is mandatory.
(i) Measuring Instruments/CMM & Gauges
(ii) Radiography Testing facility duly certified by the Government
(iii) Material Chemical & Physical facility with NABL accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced.
71
8
Set
1846
EOI/PROVISIONAL/REGULARIZATION
Ordnance Equipment Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208001
1) Measuring Instruments/CMM & Gauges
2) Radiography Testing facility duly certified by the Government
3) Material Chemical & Physical facility with NABL accreditation
71
8
Set
1847
PV/OFCH/ADV REGD/JAN-20/69
Ordnance Factory Chanda
The General Manager,
Chanda
Chanda
Maharashtra
442501
PAPER & BOARD CORRUGATED AMMUNITION DOUBLE FACED FINE FLUTE TO SPECN NO. JSS:8135-08:2008 (REV. NO.3)CONFIRMING TO STD SIZE- 787 MM X 559 MM X 5 MM THICK.
Specification
PAPER & BOARD CORRUGATED AMMUNITION DOUBLE FACED FINE FLUTE TO SPECN NO. JSS:8135-08:2008 (REV. NO.3)CONFIRMING TO STD SIZE- 787 MM X 559 MM X 5 MM THICK.
Inspection Technology:
Following test as per Drg./QAP/Spec
1. GSM testing facility
2.Chemical testing facility (Moisture content,PH of water extract, Water soluble chloride, Water
soluble sulphate, Fatty acids, Ash content%, Matter soluble in ether)
Inspection Technology:
Following test as per Drg./QAP/Spec
1. n-heptane test
2. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
Inspection Technology:
Following test as per Drg./QAP/Spec
1. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
Inspection Technology:
Following test as per Drg./QAP/Spec
1. Specific gravity
2. Flash point
3. Lead %
4. Evaporation %
5.PH of water extract
6. Water soluble chlorides
7. Water soluble sulphates
8. compatibility with explosive
9. Penetration.
CONNECTOR NO. CA 3981 FOR DETONATOR CABLE ELECTRIC 1B/L TODRG. PART NO. IQX 165 GF DC NO. 36953-A DT.10-03-04 ANDPVC SLEEVE INTERNAL DIAMETER 3.00 MM AND LENGTH 25 TO 30 MM
Specification
CONNECTOR NO. CA 3981 FOR DETONATOR CABLE ELECTRIC 1B/L TODRG. PART NO. IQX 165 GF DC NO. 36953-A DT.10-03-04 ANDPVC SLEEVE INTERNAL DIAMETER 3.00 MM AND LENGTH 25 TO 30 MM
Inspection Technology:
Following test as per Drg./QAP/Spec
1. Continuity test
2. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
61
40000
Number
1848
TE NO 190401P2FO
Gun Carriage Factory
The General Manager,
Jabalpur
Jabalpur
Jabalpur,Madhya Pradesh
482011
The Tape shall be in continuous length of 110 M (Excluding Sampling) Without Any Flag Otherwise That Roll Be Treated As Short Length.
ADRDE/QMS/TGTE/T/2019/02 Date: 10/05/2019
1. Electrical non-conductivity of pins
2. Plating thickness
3. Non-conductivity test
4. n-heptane test
5.Thread gauge
6. General Engineering Equipment for measurement
Inspection Technology
1. Non continuity test (Multimeter)
2. Air tightness Test
3. n-heptane test
4. Water Leakage test
5.Plating Thickness
6. General Engineering Equipment for measurement
PACKING BOX FOR SHAPED CHARGE 90MM CONSISTING OF10 COMPONENTS TO DRG NO. HE/CAST 086 DET 1 TO 10(EXCLUDING 90MM SHAPED CHARGE & SET OF LEGS) & QAP NO. HEMRL/HE/ADD/08/01 REV. 00 OF 09/2008
Specification
PACKING BOX FOR SHAPED CHARGE 90MM CONSISTING OF10 COMPONENTS TO DRG NO. HE/CAST 086 DET 1 TO 10(EXCLUDING 90MM SHAPED CHARGE & SET OF LEGS) & QAP NO. HEMRL/HE/ADD/08/01 REV. 00 OF 09/2008
1. Timber processing Unit (Cutting, Finishing,Polishing,Painting)
2. Pressure impregnation plant for preservative treatment (As per specification IA 948)